![\"2015-12-03-154838\"](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2015\/12\/2015-12-03-154838-350x251.jpg\")
Following the launch mishap of the Orb-3 mission in October 2014, Orbital ATK contracted with ULA for two launches of their Cygnus vehicles on an Atlas V. <\/p>\nOrbital ATK\u2019s Cygnus OA-7 resupply craft, the S.S. John Glenn, was berthed at the ISS Saturday morning. The OA-7 Cygnus \u2013 packed with equipment and supplies for the Expedition 51 crew \u2013 launched Tuesday aboard a ULA Atlas V rocket and performed orbit raising and refinement burns as it waited its turn for arrival at ISS, having to slip in after the Soyuz MS-04 spacecraft launched and docked on Wednesday.<\/p>\n<\/p>\n
Cygnus OA-7 Arrival:<\/b><\/p>\n
Launch of the OA-7 Cygnus resupply vehicle marked a return to United Launch Alliance (ULA) and Atlas V launch operations for Orbital ATK. <\/p>\n
Following the launch mishap of the Orb-3 mission in October 2014, Orbital ATK contracted with ULA for two launches of their Cygnus vehicles on an Atlas V. <\/p>\n
Those two missions \u2013 OA-4 and OA-6 \u2013 were successfully flown out of Cape Canaveral Air Force Station SLC-41 in Florida in December 2015 and March 2016, respectively.<\/p>\n
After OA-6, launch operations for Cygnus shifted back to the newly upgraded Antares rocket \u2013 Orbital ATK\u2019s internally-developed launch vehicle \u2013 which successfully returned to flight on 17 October 2016 from the Mid-Atlantic Regional Spaceport at Wallops, Virginia.<\/p>\n
With Antares making her comeback from the Orb-3 failure, the launch vehicle gained high praise from Orbital ATK, who noted the vehicle\u2019s excellent performance as it pushed the enhanced Cygnus module toward orbit and a rendezvous with the International Space Station.<\/p>\n
However, despite Antares\u2019 successful Return To Flight, NASA began discussions with Orbital ATK shortly thereafter, asking the commercial company to take advantage of the Atlas V rocket\u2019s ability to pack more payload into Cygnus and therefore switch the OA-7 mission from Antares to an Atlas V. <\/p>\n
With ULA\u2019s introduction of their RapidLaunch service agreement \u2013 which can take a rocket from contract signature to launch in just four months or even less depending on mission specifics, Orbital ATK was able to oblige NASA\u2019s request and purchase an Atlas V just four months prior to OA-7\u2019s original liftoff target.<\/p>\n
![\"\"](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2017\/04\/Screen-Shot-2017-04-21-at-09.15.25-350x232.png\")
After over a month\u2019s worth of delays, an Atlas V rocket successfully launched the OA-7 Cygnus into orbit Tuesday morning, with an on-time lift off of 11:11:26 EDT (15:11:26 GMT) from SLC-41 at the Cape Canaveral Air Force Station.<\/p>\n
With Wednesday\u2019s successful launch and rapid sequence docking of the Soyuz MS-04 spacecraft with two new residence for the Expedition 51 crew, Cygnus completed her orbit-raising and refinement burn sequences to properly align with the International Space Station for the commencement of Final Approach operations.<\/p>\n
During this \u201ccoast to ISS\u201d phase of her mission, Orbital ATK Cygnus controllers in Dulles, Virginia, commanded the craft through the first of a series of rendezvous phasing burns (called DV \u2013 Delta Velocity burns) to refine the spacecraft\u2019s trajectory toward the Station.<\/p>\n
![](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2017\/04\/2017-04-18-034349.jpg\")
The first DV burn was conducted in the early phasing period. Lasting approximately 10 minutes, the burn raised Cygnus from its initial near-circular 230 km orbit to the 400 km orbit of the ISS.<\/p>\n
A similarly long DV burn followed to again raise Cygnus to its proper orbital altitude.<\/p>\n
This was then followed by a phasing burn to align Cygnus into the exact orbital corridor of the Station.<\/p>\n
A final set of DV burns \u2013 conducted over the past two days \u2013 then brought Cygnus to its \u201cGo\/No-Go for Joint-Ops\u201d decision point, which it reached roughly five hours prior to capture.<\/p>\n
Once Cygnus received the \u201cgo\u201d from MCC-H (Mission Control Center \u2013 Houston) for Joint Ops, Cygnus began to slowly approach the Station.<\/p>\n
![\"\"](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2017\/04\/Screen-Shot-2017-04-21-at-09.20.44-350x263.png\")
The craft reached the Joint Targeting Reference Point (JTRP) just over three hours prior to capture at approximately 03:00 EDT (07:00 GMT).<\/p>\n
From this point until capture and berthing, every step of the rendezvous required a strong communications link with Cygnus.<\/p>\n
This comm link between Cygnus, the ISS, and ground controllers is routed through the JEM (Japanese Experiment Module) PROX system and ensures the ability to manually abort \u2013 or at least retreat \u2013 Cygnus\u2019 approach to the Station in the event of a problem with the spacecraft or the ISS.<\/p>\n
While aborts during proximity ops are rare, they do happen \u2013 as was seen in February with CRS-10 Dragon\u2019s arrival that had to be aborted because of a relative GPS hardware issue.<\/p>\n
![\"ISS](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2012\/06\/Z6.jpg\")
For the OA-7 Cygnus, once the craft arrived at the JTRP, the S.S. John Glenn stopped all relative motion with the ISS and awaited a second \u201cGo\/No-Go\u201d decision from MCC-H.<\/p>\n
Arrival at the JTRP also marked the beginning of the Joint Operations Phase (JOPS) of approach, as overviewed in documentation in L2.<\/p>\n
Approximately three hours before capture, and with MCC-H providing a \u201cgo\u201d to proceed, Cygnus performed the first of four ADV thruster burns (ADV1) to begin moving closer to Station.<\/p>\n
During these proximity ADV burns, Cygnus \u2013 until capture \u2013 used the TriDAR vision system designed by the Canadian company Neptec with support from NASA and the Canadian Space Agency.<\/p>\n
![\"Image](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2012\/06\/A107.jpg\")
TriDAR \u2013 tested during several Space Shuttle missions \u2013 provides Cygnus controllers with real-time visual guidance for navigation, rendezvous, and docking procedures.<\/p>\n
After the first two ADV burns, the ISS crew maneuvered the Station to its capture attitude \u2013 a 5 minute process that took place just over two hours prior to Cygnus\u2019 targeted capture time.<\/p>\n
Once Station has been reoriented, MCC-H issued another \u201cGo\/No-Go\u201d decision for the final two ADV burns of Cygnus.<\/p>\n
The third and fourth ADV burns brought Cygnus to its 250 m hold point below the ISS.<\/p>\n
MCC-H then gave the \u201cgo\u201d for Cygnus to depart the 250 m hold point and enter the Keep Out Sphere (KOS) of the ISS.<\/p>\n
![\"\"](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2017\/04\/2017-04-22-103807-350x196.jpg\")
Cygnus then pulsed its thrusters and enter the KOS \u2013 at which point NASA controllers at MCC-H joined the Orbital ATK control team for the final close proximity ops of rendezvous and berthing for the OA-7 Cygnus.<\/p>\n
Just under half an hour prior to capture, Cygnus arrived at the 30 m Hold Point.<\/p>\n
Five minutes later, Cygnus received the \u201cgo\u201d to proceed to the Capture Point, at which time it departed the 30 m Hold Point just over 15 minutes prior to capture.<\/p>\n
Cygnus then arrived at its capture point 12 m from the ISS about 8 minutes prior to the first capture attempt from Expedition 51 astronauts Thomas Pesquet and ISS Commander Peggy Whitson.<\/p>\n
![\"\"](\"\/\/www.nasaspaceflight.com\/wp-content\/uploads\/2017\/04\/2017-04-22-104909-350x266.jpg\")
Using the Station\u2019s 17.5 m Space Station Remote Manipulator System (SSRMS) robotic arm to grab hold of Cygnus, capture occurred at approximately 06:05 EDT (10:05 GMT).<\/p>\n
After Cygnus was firmly in the SSRMS\u2019s snares, Pesquet and Whitson maneuvered the S.S. John Glenn to Node-1 Unity (delivered by Space Shuttle Endeavour during the first ISS construction mission in December 1998), where the craft was berthed to the ISS at approximately 08:40 EDT (12:40 GMT).<\/p>\n
Later on Saturday, the crew will start to unpack the 3,376 kg (7,443 lbs) of research equipment, spare parts, crew supplies, and goodies.<\/p>\n
The OA-7 Cygnus is scheduled to remain attached to the Space Station for 88 days, which would place unberthing on 19 July 2017.<\/p>\n
(Images: NASA, Jacques Van Oene, and L2 including renders from L2 artist Nathan Koga \u2013 The full gallery of Nathan\u2019s (SpaceX Dragon to ITS, SLS, Commercial Crew and more) L2 images can be *found here*)<\/p>\n","protected":false},"excerpt":{"rendered":"
Orbital ATK\u2019s Cygnus OA-7 resupply craft, the S.S. John Glenn, was berthed at the ISS Saturday morning. The OA-7 Cygnus \u2013 packed with equipment and supplies for the Expedition 51 crew \u2013 launched Tuesday aboard a ULA Atlas V rocket and performed orbit raising and refinement burns as it waited its turn for arrival at […]<\/p>\n","protected":false},"author":1,"featured_media":30244,"comment_status":"","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"inline_featured_image":false,"footnotes":"","_links_to":"","_links_to_target":""},"categories":[2],"tags":[2304,639,233],"class_list":["post-38824","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-news","tag-crs","tag-cygnus","tag-iss"],"acf":[],"_links":{"self":[{"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/posts\/38824"}],"collection":[{"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/comments?post=38824"}],"version-history":[{"count":0,"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/posts\/38824\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/media\/30244"}],"wp:attachment":[{"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/media?parent=38824"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/categories?post=38824"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/starpath.global\/blog\/wp-json\/wp\/v2\/tags?post=38824"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}